Kennedy® Sharpening Stones

Aluminium Oxide man-made abrasive which is extremely tough enabling high speed penetration of high tensile materials without causing excessive fracturing. This resistance to fracturing makes it a versatile material suitable for general sharpening and honing applications.

3 Square Aluminium Oxide

A range of tough general-purpose sharpening stones able to give keen, even cutting edges on all straight edge cutting tools. Consistent and uniform cutting edges ensure fast cutting and longer tool life.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.

Kennedy® Jigsaw Blades

Manufactured from high quality steels to meet the demands of most industrial and DIY applications. Supplied display carded. High teeth per inch (TPI) blades will be slower cutting and produce a better edge finish. Low teeth per inch blades will be faster cutting but produce coarse edges on the workpiece. Different materials will also give different edge finishes depending on the make up of the material and direction of cut in relation to the direction of the grain. When cutting in some metals lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw baseplate reducing the gap around the blade and reducing the splinter area. Another technique is to score a guide line on the wood creating a pre-cut line that must then be followed accurately. The last technique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made.

Straight Shank Suitable for Fein, Wolf and Kress. HCS - Heavy Duty (Pack 5)

Capacities: Steel 3.0 - 6.0mm, Aluminium 1.0 - 3.0mm, Plastics 6.0mm. Tooth pitch: 3.0. Effective length: 50mm. Wavy set teeth. Equivalent to Wolf 91485.

Kennedy® In-line RCD

The in line RCD is wired directly into the cable between the appliance and a standard three pin 13A plug (follow the wiring diagram supplied).

Kennedy® Depressed Centre and Flat Reinforced Grinding Discs

All Kennedy Depressed Centre and Flat Reinforced Cutting wheels now carry the "oSa" (The Organisation for the Safety of Abrasives) mark of approval. "oSa" is an association of the world's leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels. Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. "oSa" marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA.

Type 41 Flat Reinforced Cutting

For use with all portable angle grinders. 180mm to 230mm discs can also be used on circular saws, and 300 to 350mm discs are for use with chop saws/cut-off machines, subject to bore compatability. Not to be used for wet cutting.
Grade A24 - For general purpose cutting on metals.
Grade C24 - For general purpose cutting on stone.

Kennedy® Bench Stones

Silicon Carbide man-made abrasive with very hard, sharp particles. This makes it ideal for non-ferrous metals, hard surfaces, alloys and cemented carbides. Also used on stone, marble, glass and plastics. A superior abrasive that is able to penetrate and cut quickly with only light pressure being applied.

Single Grit Silicon Carbide

For workshop use. Ideal for sharpening chisels, plain iron and virtually any metallic implements. Available in two types.

Kennedy® Aluminium Oxide Cloth

Superflex Aluminium Oxide is resin bonded over resin on a very flexible J-weight blue twill cloth. Moisture resistant and electrostatically coated for polishing flat and contoured surfaces of most materials.

Rolls

Roll size: (W)25mm x (L)50 Metres. Available in several grades.

Kennedy® Spare Halogen Bulbs

Halogen. Suitable for use with all standard PIR lights mini-pod floodlights, tripod site lights etc.

Halogen Tube Bulbs

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness. Operating speed range is 6000-40000rpm.

Cylindrical Plain End

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.