Kennedy® Tie Cord Bonnet Support Pads

High quality 23mm foam pads with rigid back plates. For use with all tie cord bonnets. Bonnets supplied separately. Max 2500rpm. (125mm and 150mm pads are dual purpose - also for use with Velcro bonnets or foams).

Bonnet diameters available: 125mm, 150mm, 180mm, and 200/225mm.
Thread sizes: M14 x 2 and 5/8" UNC.

Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HSS - Heavy Duty (Pack 5)

Capacities(mm): Aluminium:10.0. Plastics: 20.0. Tooth Pitch: 2.0. Effective length: 75mm. Tapered & ground. Equivalent to Bosch T101A.

Kennedy® Sharpening Stones

Silicon Carbide man-made abrasive with very hard, sharp particles. This makes it ideal for non-ferrous metals, hard surfaces, alloys and cemented carbides. Also used on stone, marble, glass and plastics. A superior abrasive that is able to penetrate and cut quickly with only light pressure being applied.

3 Square Silicon Carbide

A range of tough general-purpose sharpening stones able to give keen, even cutting edges on all straight edge cutting tools. Consistent and uniform cutting edges ensure fast cutting and longer tool life.

Kennedy® Router Cutters

To form corner radius to shelves, table tops, etc. With ball bearing guide for curved work.

Two Flute Rounding Over Bits

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'W' Shape. Shank Dia. 10mm

Shape W244. Grade: RA46. Diameter: 50mm. Length: 50mm. Max. rpm: 11,000. Weight per 10: 2670g.

Kennedy® Economy Emery Cloth

The emery abrasive particles are bonded by a high strength glue to a flexible J-weight blue twill backing cloth. The backing cloth allows the abrasive sheet to conform to the shape of the item being worked on, ensuring the abrasive action is always where you require it. Suitable for general-purpose, light duty workshop use.

Sheets

Can be torn along the grain of the cloth to the size you require to minimise wastage. Sheet size: 230 x 280mm (9" x 11"). Supplied in packs of 50.

Kennedy® Power Tool Chisels

Suitable for air and electric hammers and breakers, for all classes of work.

Kango Style Chisels

For Kango: 501, 627, 628, 637, 638, 430 - Type 750 Shanks. 19mm Hex Shank with Single Flat and Round Tang.

Kennedy® Router Cutters

Cutter for deep mortising and grooving. Staggered cutting edges give good chip clearance enhancing quality of cut.

Two Flute Staggered Tooth Bits

Kennedy® 4-Way Ultra Slim Socket Extension

4-way. 240V. 3M cable. Allows appliances not exceeding 13 amps to be plugged into 1 socket outlet. Conform to BS 1363 Part 1: 1995.