产品 / 动力工具 & 磨料磨具
编号：KEN2501820K
●产品描述：
Kennedy® Mounted Points and Wheels
Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.
'W' Shape. Shank Dia. 3mm
Shape W182. Grade: RA60. Diameter: 13mm. Length: 3mm. Max. rpm: 70,000. Weight per 10: 40g.
编号：KEN2881420K
●产品描述：
Kennedy® M2 Multi-Tooth Milling Cutters
Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.
Short Series
Shank dia.: 19mm/3/4".
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm.
编号：KEN2881200K
●产品描述：
Kennedy® M2 Multi-Tooth Milling Cutters
Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.
Short Series
Shank dia.: 19mm/3/4".
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm.
编号：KEN2875260K
●产品描述：
Kennedy® Router Cutters
General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.
Two Flute Straight Plunging Bits
编号：KEN2873520K
●产品描述：
Kennedy® Router Cutters
With Ball Bearing Guide. To trim laminate producing a bevelled edge. With ball bearing guide suitable for straight or shaped work.
Bevel Edge Trimming Bits
编号：KEN2502110K
●产品描述：
Kennedy® Mounted Points and Wheels
Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.
'W' Shape. Shank Dia. 3mm
Shape W211. Grade: RA80. Diameter: 22mm. Length: 3mm. Max. rpm: 43,000. Weight per 10: 60g.
编号：KEN2554100K
●产品描述：
Kennedy® Bench Stones
Silicon Carbide man-made abrasive with very hard, sharp particles. This makes it ideal for non-ferrous metals, hard surfaces, alloys and cemented carbides. Also used on stone, marble, glass and plastics. A superior abrasive that is able to penetrate and cut quickly with only light pressure being applied.
Single Grit Silicon Carbide
For workshop use. Ideal for sharpening chisels, plain iron and virtually any metallic implements. Available in two types.
编号：KEN2801110K
●产品描述：
Kennedy® 3 Pin Plugs for Site Use
Fitted with fully waterproof spring loaded caps. Rated to 16A over 6 hours. Colour coded: 110V yellow, 240V blue. Conform to BS 4343 : 1968.
编号：KEN2870120K
●产品描述：
Kennedy® Router Cutters
For cutting grooves/apertures and general shaping work. Single flute for maximum support behind the cutting edge, giving strength, while providing large clearance for ease of chip flow promoting fast free cutting.
Single Flute Straight Plunging Bits
编号：KEN2874540K
●产品描述：
Kennedy® Router Cutters
General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.
Two Flute Straight Plunging Bits