Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.
N.B. - 3mm Shank

Ball Shape

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'B' Shape. Shank Diameter 3mm

Shape B106. Grade: RA100. Diameter: 3mm. Length: 3mm. Max. rpm: 100,000. Weight per 10: 20g.

Kennedy® Abrasive Files

Aluminium Oxide man-made abrasive which is extremely tough enabling high speed penetration of high tensile materials without causing excessive fracturing. This resistance to fracturing makes it a versatile material suitable for general sharpening and honing applications.

Half Round Aluminium Oxide

A range of tough general-purpose sharpening stones able to give keen, even cutting edges on all straight edge cutting tools. Consistent and uniform cutting edges ensure fast cutting and longer tool life.

Kennedy® Flexible Backing Pads For 'Velcro' Sanding Discs

Suitable for use with Kennedy
Hook & Loop and other
‘velcro-type’ sanding discs

Kennedy® 5 Piece Industrial Wire Brush Set

All supplied in clear bag with header.

Industrial Wire Brush Set (5 Piece)

Contents: (1 off each):
Shaft mounted circular brushes 30 x 12, 50 x 10 & 50 x 20.
Flat end de-carbonising 12 x 20.
Pointed end de-carbonising 12 x 20.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'B' Shape. Shank Diameter 3mm

Shape B92. Grade: RA120. Diameter: 6mm. Length: 6mm. Max. rpm: 81,000. Weight per 10: 20g.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'A' Shape. Shank Diameter 6mm

Shape A37. Grade: RA80. Diameter: 32mm. Length: 6mm. Max. rpm: 30,000. Weight per 10: 160g.

Kennedy® Velcro-Backed Sanding Discs

No spanners required to change discs. 100% of sanding disc can be used, material removal rate is therefore increased. Can be repeatedly removed and re-applied again and again. Unaffected by dust or moisture. Aluminium oxide abrasive "resin-bonded over resin" to Velcro backed paper suitable for wood, plastics, ceramics etc.

Plain (No Holes)

Diameter: 150mm.

Kennedy® Slip Stones

Silicon Carbide man-made abrasive with very hard, sharp particles. This makes it ideal for non-ferrous metals, hard surfaces, alloys and cemented carbides. Also used on stone, marble, glass and plastics. A superior abrasive that is able to penetrate and cut quickly with only light pressure being applied.

Silicon Carbide

For sharpening curved edge cutting tools.

Kennedy® Bench Stones

Aluminium Oxide man-made abrasive which is extremely tough enabling high speed penetration of high tensile materials without causing excessive fracturing. This resistance to fracturing makes it a versatile material suitable for general sharpening and honing applications.

Single Grit Aluminium Oxide

For workshop use. Ideal for sharpening chisels, plain iron and virtually any metallic implements. Available in two types.