York? High Performance Flap Discs

High performance alternative to sanding discs. Have the advantage over depressed centre grinding discs on light gauge sheet metal where surface finish is important. Overlapped abrasive strips slowly wear away revealing fresh abrasive, ensuring the disc always cuts effectively, reducing clogging, provides constant finish throughout disc life, generates less noise and heat - less blueing. No backing pads needed - fits directly onto machine. Safe to use at 80m/s on any grinder. Tested at 150m/s and approved by the German Grinding Wheel Authority (DSA).

Zirconium Grade Glass Fibre Backed (For Stainless Steel - Non-Scratch).

100mm Dia x 16mm Bore 15,300 MOS (rpm).

York Grinding Wheels

Vitrified bond for precision grinding. Unaffected by water, acid and oils. All 1,1/4?? bore, supplied with 1??, 7/8??, 3/4??, 5/8?? & 1/2?? bore nylon bushes. Tough general-purpose aluminium oxide which is hard wearing. Used for surface and off hand grinding. Refined aluminium oxide with a faster grinding operation. Suitable for high speed steels, precision grinding and general surface grinding. Silicon carbide, used on low tensile strength materials, non ferrous metals and carbide tool grinding. All York grinding wheels are supplied in a unique storage box, which helps prevent chipping and other accidental damage. Spare cases available on request.

1,1/4" Bore

York? Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.
N.B. - 3mm Shank

Cylindrical Ball Nosed

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

York? Flap Wheels

Shaft mounted flap wheels can be used in portable air or electric power tools, including tyre buffers, flexible shafts and hand drills. Manufactured from highest quality industrial cloth. Used for a wide range of applications such as removal of rust, cleaning up welds and sanding wood prior to painting. Boxed in 10's 6's. Recessed hub design for maximum access in tight corners.

6mm Shank

60mm Dia x 50mm Height 10,200 MOS (rpm)

York? Diamond Coated Burrs

3mm shank. Overall length 45mm. Diamond grip mesh is 120/140. Recommended operating speeds 15,000 30,000 RPM. Suitable for precision grinding of carbide, gems, ceramics, tough alloys, cermets, tool steels etc.

Ball Nosed

York? Flap Wheels

Shaft mounted flap wheels can be used in portable air or electric power tools, including tyre buffers, flexible shafts and hand drills. Manufactured from highest quality industrial cloth. Used for a wide range of applications such as removal of rust, cleaning up welds and sanding wood prior to painting. Boxed in 10s except for 60 x 50 and 80 x 50 which are packed in 6s. Recessed hub design for maximum access in tight corners.

6mm Shank

60mm Dia x 20mm Height 10,200 MOS (rpm)

York? Abrasives Pre-Finish & Polishing Compounds

York? Abrasives have a compound bar for every polishing job! They are manufactured using the finest quality ingredients to ensure that you get the highest quality results every time on all metals, plastics and glass. They are excellent high performance polishing compounds, not too waxy and not too dry.

For the full range of York? Abrasives polishing mops and compounds please refer to our catalogue.

Bright Shine Pre-Finish Polishing Compound Bar

This bar has a composition that gives good cutting characteristics and also leaves a bright finish when used with our sisal mops. Dimensions: 43x218x55mm (HxWxD). Average weight: 800g.

York? Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness. Operating speed range is 6000-40000rpm.

Cylindrical Ball Nosed

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

York? Depressed Centre Grinding Discs

Manufactured to assure operator safety and optimum performance. For use with all portable angle grinders. Not to be used for ?free hand? or wet grinding. Optimum angle for use 25 to 35.

Type 27

Grade A30/A24. For general-purpose use on metals.

York? Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness. Operating speed range is 6000-40000rpm.

Cylindrical Plain End

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.