Engis Hyprez Oilstones

Manufactured from carefully graded abrasive particles, mixed with the appropriate bonding agents and fired in electric or gas ovens to produce a stone suitable for roughing out cavities and dies to commercial finishes.

Hyprez D.S. Medium/Soft Aluminium Oxide

This is a popular, fast-cutting stone which does not load easily. Good for all dies and moulds. Length: 150mm.

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.
N.B. - 3mm Shank

Cylindrical Ball Nosed

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Trend Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

1/4" and 1/2" Shanks

Hitachi Nibblers

CN16SA
Lightweight design with slimline grip. Fast cutting speed of 1.8m/min (mild steel plate). Downward cutting action permits cutting of trapezoidal metal plate and minimises scattering of chips on workpiece. Three position indexing die holder allows quick and easy change of cutting direction.

Specifications:
Cutting capacity: mild steel 1.6mm, S/steel: 1.2mm, aluminium plate: 2.3mm.
Power input: 400W.
No load speed 2300/min.
Min cutting radius: 40mm.
Length: 250mm.
Weight: 1.7kg.
Standard Accessories: die, punch and 2 wrenches.

Available in 240V and 110V.

Trend Router Cutters

With ball bearing guide. To trim plastic or laminate facings. Used extensively in cabinet making and shop fitting. Suitable for straight or curved work.

Two Flute Flush Trimming Bits

1/4" and 1/2" Shanks

3M Roloc? Disc Products

Designed for use on portable tools and featuring the convenient Roloc? Twist-on, Twist-off fixing system.

Roloc? Disc Holders

All holders on 6mm shank.

Cubitron™ Fibre Sanding Discs

Cubitron™ II Fibre Discs are made with revolutionary 3M precision shaped ceramic grain technology, engineered with ultra-sharp, fast-cutting points that wear evenly, run cool and optimize mineral breakdown to maximize disc life.
Get more productivity, throughput, disc life, comfort and grinding speed.

Model D420 x 1500 420mm Swing x 1500mmDBC 3ph 0340-1165

Induction hardened and precision ground heavily ribbed prismatic bed. Substructure and lathe bed made from a single block of Meehanite cast iron. Camlock spindle nose D1-6. Oil-quenched hardened work spindle bedded in two readjustable precision taper roller bearings. Guaranteed concentricity precision of the spindle nose 0.015mm. Smooth running work spindle gearwheels hardened and precision ground. Leadscrew and feed shaft drive easily switchable via oil quenched feed gear. Adjustable safety coupling of the feed shaft. The tailstock may be shifted plus/minus for taper turning. Right - left - hand rotation can be switched with the help of the indexing spindle. Emergency stop mushroom switch, lockable main switch. Removable gap bed. Adjustable dial of the threading gauge. Mechanical foot spindle brake. Manufactured to DIN 8606 (toolmakers precision).

Standard accessories:
200mm 3 jaw chuck, 250mm 4 jaw chuck, 350mm face plate, steady rest, follow rest, coolant system, rear splash guard, spindle brake, 2-step drive motor, electrically interlocked chuck guard, turret limit stop with fine adjustment acting as end stop on lathe saddle, machine lamp, threading gauge, operating tools.

Specifications:
Between centres: 1500mm.
Centre height: 210mm.
Max.turning diameter: 420mm.
Max turning diameter over saddle: 255mm.
Max turning diameter over gap: 590mm.
Bed width: 250mm.
Spindle hole: 52mm.
Spindle taper: 6MT.
Tailstock taper: 4MT.
Spindle: D1-6.
No of spindle speeds: 16.
Spindle speeds: 45-1800rpm.
Longitudinal feeds: 0.05-1.7mm/rev.
Cross feeds: 0.025-0.85mm/rev.
Pitch metric (39): 0.2-14mm.
Pitch inch (45): 2-72 TPI
Modular thread (18): 0.3-3.5 MP
Trapezoid thread (21): 8-44 DP.
Top slide travel: 140mm.
Cross slide travel: 230mm.
Sleeve travel: 120mm.
Max. Tool shank: 20mm.
Main motor power: 4.5kW.
Coolant pump: 0.1kW.
Size (LxWxH): 245x91x135cms.
Weight: 1950kg.

Dronco Diamond Cutting Blades

A top end quality product gives a good cutting performance on both hard and abrasive materials. This blade also cuts re-inforcements. No cooling breaks required. Can be used dry or wet cutting. Laser welded

Evolution Cool Formula

Makita Batteries for Cordless Tools

Charger compatibility: DC1414F, DC1439, DC1822, DC1804F.

NiCd Batteries - ?Plug-In? Type