Kennedy® Depressed Centre and Flat Reinforced Grinding Discs

All Kennedy Depressed Centre and Flat Reinforced Cutting wheels now carry the "oSa" (The Organisation for the Safety of Abrasives) mark of approval. "oSa" is an association of the world's leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels. Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. "oSa" marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA.

Type 42 Depressed Centre Cutting Discs

For use with all portable grinders/cut-off machines. Not to be used for grinding. Grade A24 - for general-purpose use on metals.

Makita Batteries for Cordless Tools

Charger compatibility: DC18RA, DC18SE, DC24SC, DC24WA.

NiMh Batteries - ?Slide-On? Type

York? Mandrels

For use with Cartridge Rolls. This steel adaptor is used to secure and hold both tapered and parallel sided cartridge rolls to air grinders or electric drills. This holder is used by sliding the cartridge roll onto the mandrel pilot until the bottom of the abrasive touches the threaded steel area. Simply screw the cartridge roll onto the threads to secure. Your mandrel should be at least 13mm longer than your cartridge roll.

Kennedy® Aluminium Oxide Cloth

Superflex Aluminium Oxide is resin bonded over resin on a very flexible J-weight blue twill cloth. Moisture resistant and electrostatically coated for polishing flat and contoured surfaces of most materials.

Sheets

Size: (W)230mm x (L)280mm. Available in several grades.

3M Scotch-Brite Surface Conditioning Discs

For removing grinding marks and scratches leaving a greatly improved surface finish. Centre pin system contributes to a reduction in hand-arm vibration due to centred secure fixing system.

Hook and Loop Backed - 100 x 16mm

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'W' Shape. Shank Dia. 6mm

Shape W227. Grade: RA46. Diameter: 32mm. Length: 13mm. Max. rpm: 30,000. Weight per 10: 230g.

York? Sanding Bands

Spiral wound with tear resistant backing fabric. For grinding and finishing edges, profiles, welded joints etc. For use with power tools. Aluminium Oxide for use on most metals. Available in several sizes.

Aluminium Oxide Sanding Bands

Size: (Dia)75mm x (W)30mm.

Kennedy® Depressed Centre and Flat Reinforced Grinding Discs

All Kennedy Depressed Centre and Flat Reinforced Cutting wheels now carry the "oSa" (The Organisation for the Safety of Abrasives) mark of approval. "oSa" is an association of the world's leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels. Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. "oSa" marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA.

Type 41 Flat Reinforced Cutting

For use with all portable angle grinders. 180mm to 230mm discs can also be used on circular saws, and 300 to 350mm discs are for use with chop saws/cut-off machines, subject to bore compatability. Not to be used for wet cutting.
Grade A24 - For general purpose cutting on metals.
Grade C24 - For general purpose cutting on stone.

York? Diamond Coated Burrs

3mm shank. Overall length 45mm. Diamond grip mesh is 120/140. Recommended operating speeds 15,000 30,000 RPM. Suitable for precision grinding of carbide, gems, ceramics, tough alloys, cermets, tool steels etc.

Cylindrical

Kennedy® Wire Wheels & Brushes

For use in high speed air and electrical tools. Ideal for hard to reach areas. For the removal of paint, carbon and for de-burring. 6mm Shanks. 30 SWG
Brush manufactured from Steel wire and holder and shank manufactured from galvanized steel.

Pointed End Decarbonising Brushes