Ajax Bench Grinders and Polishers

Machine pedestal for use with Arboga double ended grinders and polishers models: BGE6, BGE8, BGE10.

Pedestal only - machine not included.

Arboga BGE Machine Pedestal

Norton Depressed Centre Reinforced Cutting & Grinding Discs

A range of discs for all angle-grinding of both metal (aluminium oxide) and stone (silicon carbide).

Kennedy® Wire Wheels & Brushes

Industrial rotary wire wheels & brushes are available as a comprehensive range including circular brushes, shaft mounted arbor style and de-carbonising brushes for use with power tools, machine tools and flexible drives.

Cup Brushes - Threaded Bore

Multi purpose brush for removal of rust, paint and burrs. Ideally suited for use on bench machines and angle grinders. 30 SWG

Kennedy® Abrasive Files

Silicon Carbide man-made abrasive with very hard, sharp particles. This makes it ideal for non-ferrous metals, hard surfaces, alloys and cemented carbides. Also used on stone, marble, glass and plastics. A superior abrasive that is able to penetrate and cut quickly with only light pressure being applied.

Round Silicon Carbide

A range of tough general-purpose sharpening stones able to give keen, even cutting edges on all straight edge cutting tools. Consistent and uniform cutting edges ensure fast cutting and longer tool life.

York? Cartridge Rolls

Spirally wound Aluminium Oxide cloth rolls that wear in use constantly exposing new abrasive. Used for weld flash removal, deburring, blending and polishing applications. Available in two types. A steel mandrel must be used to secure the abrasive to the tool.

Taper Type

Tapered for angles, corners and irregular or concave surfaces.

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.

Conical

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'B' Shape. Shank Diameter 3mm

Shape B44. Grade: RA100. Diameter: 6mm. Length: 10mm. Max. rpm: 68,000. Weight per 10: 150g.

Kobe IW500 1/2" Impact Wrench

The Kobe IW500 1/2" square drive air impact wrench is suitable for the rapid removal or installation of threaded fasteners. The housing is manufactured from a single piece of aluminium, for increased strength and durability. The housing has a rubber shroud around the square drive to protect the surface of the work piece from accidentally impacts and a rear bumper to protect the tool when it?s not in use. Reverse gear is selected easily at the press of a button conveniently located above the 10 position throttle control. The short body length allows access into hard to reach areas.

IW500 - 1/2" Impact Wrench

One piece aluminium housing, 10 position power regulator and thumb switch for reversing.

Specifications:
Bolt capacity: 16mm.
Torque: 325 Nm.
Air inlet thread: 1/4" NPT.
Air hose size (ID): 8mm.
Air pressure: 90PSI.
Air consumption: 4CFM*.
Overall length: 191mm.
Weight: 2.4kg.
Noise level: 88dB(A).
Vibration: 4.2m/s2.
For a complete range of 1/2'' drive impact sockets see product group KEN-583.

*Based on 15 second cycle per minute average use.

NiCad Batteries - Bulb

2607335021 12.0V 1.5Ah GML24V/VCD, AL2422DC, AL2425DV, AL2450DV, AL2498FC

Kobe? Pistol Grip Air Hammer

HP4540
Suitable for use with cutters, punches, spot weld breakers and flat chisels. Supplied with retainer spring. Accepts all standard 0.401" shank tools.

Specifications:
1/4?? NPT air inlet thread for 10mm air hose.
90PSI air pressure.
4CFM* air consumption.
Overall length: 145mm.
Stroke length: 40mm.

*Based on a 15 second cycle per minute average use.