Vari Turret Milling Machine

ETM-2VS R8 Variable Speed 1-199-200
3 AXIS DRO. Power feed to three axis. Versatile machine for drilling - milling and boring operations. Heavy-duty and sturdy machine is made of meehanite casting of generous proportion. Rigid machine is rated for continuous use and will give you longer life expectancy. Accurate engineering tolerances have been met by highly skilled engineers during manufacture. 3HP motor allows you to take large cuts during your production runs. R8 spindle allows you to use a large selection of standard tooling. Automatic stop is to up/down feed at the end of the pre-set travel. Angular positioning to left/right through worm and gear for ease. Reversible switch allows you to run spindle clock and counter clock wise. Centralised one-shot lubrication ensures lubrication to all parts otherwise inaccessible. Metric dials with DRO allow you to work in either Inch or Metric calibrations. Hardened slide ways gives the machine much longer production life. Quill feed at three rates of feed give you the option to select the correct feed to quill to suit your individual production requirements. Servo type variable longitudinal cross and vertical feed and rapid. Electrically interlocked spindle guard conforms to the latest CE regulations and Health and Safety Standards.

Standard accessories:
Power feed to quill - three rates. Servo type longitudinal, cross and vertical feed and rapid.
One shot lubrication.
Coolant system.
Electrically interlocked spindle guard.
Low volt machine light.

Specifications:
Table size: 228 x 1245mm.
Table travel (long): 838mm.
Saddle travel (cross): 300mm.
Knee travel (vertical): 400mm.
Quill travel: 127mm.
Ram travel: 315mm.
Spindle motor: 2.2KW (3HP).
Spindle taper: R8.
Quill power feed: 0.04, 0.08, 0.15mm/rev.
Spindle speeds: 70 - 4200 variable speed.
Overall length: 1700mm.
Overall width: 1600mm.
Overall height: 2130mm.
Spindle to table: min. 0mm, max. 415mm.
Spindle to column: min 170mm, max 485mm.
Weight: 100kg.

Trend Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

1/4" and 1/2" Shanks

Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

Osaki™ Garden Power Tools

The Osaki™ Garden Power Tools ABV2000 leaf blower and vacuum is ideal for collecting garden debris from lawns, pathways and drives.

It will save you hours of backbreaking work raking up leaves and other garden debris. Simple to use controls switch the ABV2000 from blowing to suction with the simple flick of a switch.

A large 45-litre capacity collection bag is supplied and waste volume is reduced up to 1/10th thanks to the integral shredder unit.

ABV2000 Leaf Blower and Vacuum with Shredder

Specifications:
2000-watt electric motor produces a 250km/h blower.
Vacuum which collects 13m3/min.
Fitted with a shoulder strap for user comfort, wheels for easy manoeuvrability and a 10-metre cable.
Weight 4.70kg.
1-year guarantee.

For the full range of Osaki™ garden power tools please refer to our catalogue.

Norton Flat Reinforced Cutting Discs

A range of discs for all angle-grinding of both metal (aluminium oxide) and stone (silicon carbide).

Pilot Pins

For use with all multi-tooth milling cutters with 6mm bore. Pilots locate into pre-drilled pilot holes ensuring positional accuracy of the cutter. Suitable for 'blind' or 'through' pilot holes, pin will retract into cutter adapter on 'bottoming'. Short series equals 12mm cutter. Long series equals 13-52mm cutters.

Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HCS - Medium Duty (Pack 5)

Jigsaw Blade (Equivalent to Bosch T119A)
Application: wood 15mm, plastic 8mm.
Blade: HCS medium duty, wavy set tooth form.
Tooth pitch: 1.2mm.

Effective length: 48mm.
Pack of 5.

Engis Hyprez Oilstones

Manufactured from carefully graded abrasive particles, mixed with the appropriate bonding agents and fired in electric or gas ovens to produce a stone suitable for roughing out cavities and dies to commercial finishes.

Hyprez D.S. Medium/Soft Aluminium Oxide

This is a popular, fast-cutting stone which does not load easily. Good for all dies and moulds. Length: 150mm.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'W' Shape. Shank Dia. 6mm

Shape W230. Grade: RA46. Diameter: 32mm. Length: 32mm. Max. rpm: 20,000. Weight per 10: 700g.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'W' Shape. Shank Dia. 6mm

Shape W179. Grade: RA60. Diameter: 10mm. Length: 32mm. Max. rpm: 25,000. Weight per 10: 140g.