Zirconium Abrasive Flap Discs

'JET Zirkon' Zirconium abrasive discs with intergrated M14 adaptors for quick mounting and reinforced glass fibre backing with 'cooling slots' for air-cooling. Fully resinoid bonded with fillers for active grind support. Self-sharpening ceramic grain for extremely high stock removal as well as a long service life.

J-AZA

Kennedy® Depressed Centre and Flat Reinforced Grinding Discs

All Kennedy Depressed Centre and Flat Reinforced Cutting wheels now carry the "oSa" (The Organisation for the Safety of Abrasives) mark of approval. "oSa" is an association of the world's leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels. Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. "oSa" marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA.

Inox BF Cut-Off Discs

Iron, chlorine and sulphur free. Thin 1.0 mm discs that enable you to achieve a uniquely clean cut in the shortest possible time whilst using minimum of force. vibration-free cutting, no thermal bluing and no burring. For use on thin sheet metal, steel cable, thin-walled profile sections, stainless steel pipes and non-ferrous metals. Max. operating speed: 13280 r.p.m.

Kemet Gesswein Abrasive Stones

Manufactured from carefully graded abrasive particles, mixed with the appropriate bonding agents and fired in electric or gas ovens to produce a stone suitable for roughing out cavities and dies to commercial finishes.

Gesswein EDM Hard/Aluminium Oxide.

Specially formulated for EDM scale removal. Length 150mm.

Heat Gun

Four memory settings. Precise airflow and temperature control. Cold setting can be set for cooling heating element(approx. 1 minute). Removable dirt filter for cleaning. Ergonomic design/softgrip. Accessories: surface nozzle 50mm, glass protection nozzle 75mm and carrying case. Working temperature: 50° - 660°C. Power input: 2,300W. Airflow: 250 - 500 l/min.

GHG 660LCD

York? Flap Wheels

Shaft mounted flap wheels can be used in portable air or electric power tools, including tyre buffers, flexible shafts and hand drills. Manufactured from highest quality industrial cloth. Used for a wide range of applications such as removal of rust, cleaning up welds and sanding wood prior to painting. Boxed in 10s except for 60 x 50 and 80 x 50 which are packed in 6s. Recessed hub design for maximum access in tight corners.

6mm Shank

60mm Dia x 40mm Height 10,200 MOS (rpm)

York? Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.

Conical 90 Inc. Angle

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

3M Roloc Disc Products

Designed for use on portable tools and featuring the convenient Roloc Twist-on, Twist-off fixing system.

Surface Conditioning Discs

Reinforced Scotch-Brite web designed for cleaning and finishing on all metals. Leaves a burr-free surface for painting and coating for removal of light rust, oxides and coatings.
Maximum rpm.25mm Discs = 25000rpm.
50mm Discs = 23000rpm.
75mm Discs = 18000rpm.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Short Series

Shank dia.: 19mm/3/4".
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'W' Shape. Shank Dia. 6mm

Shape W204. Grade: RA60. Diameter: 19mm. Length: 19mm. Max. rpm: 42,000. Weight per 10: 230g.

Norton Aluminium Oxide Sheets

In the same market-leading material as Norton's "Handy Roll", these high quality aluminium oxide sheets provide excellent flexibility. Ideal replacement for "Emery Cloth."

Sheets

Sheet size: (W)230mm x (L)280mm. Available in several grades.