Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HSS - Heavy Duty (Pack 5)

Jigsaw Blade (Equivalent to Bosch T227D)
Application: steel 3 - 6mm, aluminium 3 - 15mm, plastics 30mm.
Blade: HSS heavy duty, side set teeth. For cutting curves.
Tooth pitch: 3.0mm.
Effective length: 75mm.

Kennedy® 4-Way Switched Multi Socket

13A 2mtr cable. All sockets are individually switched with neon power indicating light.

Kennedy® Router Cutters

Tungsten carbide tipped cutters to cut slots in rails to accept panels or for cutting slots in frames and doors for 'weather' feature fittings. Arbors are supplied separately.

Three Tooth Slotting/Biscuit Jointing Cutter

Kennedy® Economy Emery Cloth

The emery abrasive particles are bonded by a high strength glue to a flexible J-weight blue twill backing cloth. The backing cloth allows the abrasive sheet to conform to the shape of the item being worked on, ensuring the abrasive action is always where you require it. Suitable for general-purpose, light duty workshop use.

Rolls

Roll size: (W)25mm x (L)50 Metres. Available in several grades.

Kennedy® Aluminium Oxide Cloth

Superflex Aluminium Oxide is resin bonded over resin on a very flexible J-weight blue twill cloth. Moisture resistant and electrostatically coated for polishing flat and contoured surfaces of most materials.

Rolls

Roll size: (W)25mm x (L)50 Metres. Available in several grades.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'W' Shape. Shank Dia. 6mm

Shape W194. Grade: RA60. Diameter: 16mm. Length: 13mm. Max. rpm: 56,000. Weight per 10: 150g.

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.

Flame Shape

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Kennedy® Bench Stones

Silicon Carbide man-made abrasive with very hard, sharp particles. This makes it ideal for non-ferrous metals, hard surfaces, alloys and cemented carbides. Also used on stone, marble, glass and plastics. A superior abrasive that is able to penetrate and cut quickly with only light pressure being applied.

Single Grit Silicon Carbide

For workshop use. Ideal for sharpening chisels, plain iron and virtually any metallic implements. Available in two types.

Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HCS - Medium Duty (Pack 5)

Jigsaw Blade (Equivalent to Bosch T101BR)
Application: wood 50mm, plastics 30mm, cuts on down stroke.
Blade: HCS medium duty, tapered and ground.
Tooth pitch: 2.5mm.

Effective length: 64mm.

Pack of 5.