Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'A' Shape. Shank Diameter 6mm

Shape A38. Grade: RA60. Diameter: 25mm. Length: 25mm. Max. rpm: 35,000. Weight per 10: 200g.

Kennedy® Router Cutters

Tungsten carbide tipped cutters to cut slots in rails to accept panels or for cutting slots in frames and doors for 'weather' feature fittings. Arbors are supplied separately.

Three Tooth Slotting/Biscuit Jointing Cutter

Kennedy® M2 Multi-Tooth Milling Cutters

For use with all multi-tooth milling cutters with 6mm bore. Pilots locate into pre-drilled pilot holes ensuring positional accuracy of the cutter. Suitable for "blind" or "through" pilot holes, pin will retract into cutter adaptor on "bottoming".

Pilot Pins

Bore diameter: 20mm.
Overall length: 156mm.

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.

Pointed Tree

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Bosch Style Chisels

Suitable for air and electric hammers and breakers, for all classes of work.



For Bosch: USH27, USH28, 11304, 11308, 12314. 29mm Hex Shank with Single Flat.

Kennedy® Velcro-Backed Sanding Discs

No spanners required to change discs. 100% of sanding disc can be used, material removal rate is therefore increased. Can be repeatedly removed and re-applied again and again. Unaffected by dust or moisture. Aluminium oxide abrasive "resin-bonded over resin" to Velcro backed paper suitable for wood, plastics, ceramics etc.

Plain (No Holes)

Diameter: 150mm.

Kennedy® Router Cutters

With ball bearing guide. To trim plastic or laminate facings. Used extensively in cabinet making and shop fitting. Suitable for straight or curved work.

Two Flute Flush Trimming Bits

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.

Conical 14

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Kennedy® Aluminium Oxide Cloth

Superflex Aluminium Oxide is resin bonded over resin on a very flexible J-weight blue twill cloth. Moisture resistant and electrostatically coated for polishing flat and contoured surfaces of most materials.

Sheets

Size: (W)230mm x (L)280mm. Available in several grades.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'B' Shape. Shank Diameter 3mm

Shape B97. Grade: RA100. Diameter: 3mm. Length: 10mm. Max. rpm: 100,000. Weight per 10: 20g.