Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Short Series

Shank dia.: 19mm/3/4".
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm.

Kennedy® Wire Wheels & Brushes

For use in high speed air and electrical tools. Ideal for hard to reach areas. For the removal of paint, carbon and for de-burring. 6mm Shanks. 30 SWG
Brush manufactured from Steel wire and holder and shank manufactured from galvanized steel.

Pointed End Decarbonising Brushes

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.

Conical 60 Inc. Angle

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HCS - Medium Duty (Pack 5)

Jigsaw Blade (Equivalent to Bosch T301D)
Application: wood 760mm, plastics 50mm. For cutting curves.
Blade: HCS medium duty, tapered and ground.
Tooth pitch: 4.0mm.

Effective length: 85mm.

Pack of 5.

Kennedy® Mini-Pod FloodLight

This compact site light is constructed from diecast aluminium with a steel wire lens guard to prevent contact with the hot lens and protect it against damage. Made from top grade components and wire for industrial heavy duty use.

Mini-Pod FloodLight

Specifications: 500W tungsten halogen bulb. 3M heavy duty cable. Tempered safety glass. Epoxy coated, non-tipping frame. Soft grip rubber handle.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'B' Shape. Shank Diameter 3mm

Shape B53. Grade: RA100. Diameter: 8mm. Length: 16mm. Max. rpm: 60,000. Weight per 10: 30g.

Kennedy® Pin Spanners for Angle Grinders

Several types available. Weight 110g.

Pin Spanner

Open-ended 14 x 17mm.

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness. Operating speed range is 6000-40000rpm.

Cylindrical Plain End

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Kennedy® Velcro-Backed Sanding Discs

No spanners required to change discs. 100% of sanding disc can be used, material removal rate is therefore increased. Can be repeatedly removed and re-applied again and again. Unaffected by dust or moisture. Aluminium oxide abrasive "resin-bonded over resin" to Velcro backed paper suitable for wood, plastics, ceramics etc.

Hole Pattern: 800A. 8 Hole

Diameter: 115mm. (To suit PEX 115, PEX 9.6, Kress) dust extraction type.

Kennedy® Router Cutters

For cutting grooves/apertures and general shaping work. Single flute for maximum support behind the cutting edge, giving strength, while providing large clearance for ease of chip flow promoting fast free cutting.

Single Flute Straight Plunging Bits