Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'W' Shape. Shank Dia. 3mm

Shape W185. Grade: RA60. Diameter: 13mm. Length: 13mm. Max. rpm: 34,500. Weight per 10: 60g.

Kennedy® "Ultimate" Merino Sheepskin Bonnets

Genuine 100% sheepskin tie-on bonnets ideal for polishing metal, glass fibre, wood and painted surfaces. With tie cord. 32mm pile. Maximum 2,500rpm - Best results are obtained with a tool speed of 1,500 - 2,000rpm. Not suitable for wet use. Support pad supplied separately.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Short Series

Shank dia.: 19mm/3/4".
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm.

Kennedy® Router Cutters

Cutter for deep mortising and grooving. Staggered cutting edges give good chip clearance enhancing quality of cut.

Two Flute Staggered Tooth Bits

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.

Conical 14

Cut 3 - Rapid Cut
For use on softer non-ferrous and plastic materials i.e. aluminium, fibreglass, plastics, hard rubber and zinc alloy.

Kennedy® Velcro-Backed Sanding Discs

No spanners required to change discs. 100% of sanding disc can be used, material removal rate is therefore increased. Can be repeatedly removed and re-applied again and again. Unaffected by dust or moisture. Aluminium oxide abrasive "resin-bonded over resin" to Velcro backed paper suitable for wood, plastics, ceramics etc.

Hole Pattern: 600A. 6 Hole

Diameter: 150mm. (To suit PEX 15, GEX 150, Flex) dust extraction type.

Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HCS - Medium Duty (Pack 5)

Capacities (mm): Wood: 50.0. Plastics: 30.0. Tooth Pitch: 2.5. Effective Length: 75. Tapered & ground. Equivalent to Bosch T101B.

Kennedy® Router Cutters

To form corner radius to shelves, table tops, etc. With ball bearing guide for curved work.

Two Flute Rounding Over Bits

Kennedy® Aluminium Oxide Cloth

Superflex Aluminium Oxide is resin bonded over resin on a very flexible J-weight blue twill cloth. Moisture resistant and electrostatically coated for polishing flat and contoured surfaces of most materials.

Rolls

Roll size: (W)38mm x (L)50 Metres. Available in several grades.

Kennedy® Wire Wheels & Brushes

Industrial rotary wire wheels & brushes are available as a comprehensive range including circular brushes, shaft mounted arbor style and de-carbonising brushes for use with power tools, machine tools and flexible drives.

Additional Side Plates for Circular Brushes

Supplied free of charge with circular brushes. Please specify when ordering.