York High Performance Flap Discs

High performance alternative to sanding discs. Have the advantage over depressed centre grinding discs on light gauge sheet metal where surface finish is important. Overlapped abrasive strips slowly wear away revealing fresh abrasive, ensuring the disc always cuts effectively, reducing clogging, provides constant finish throughout disc life, generates less noise and heat - less blueing. No backing pads needed - fits directly onto machine. Safe to use at 80m/s on any grinder. Tested at 150m/s and approved by the German Grinding Wheel Authority (DSA).

Zirconium Grade Aluminium Backed (For Stainless Steel)

127mm Dia x 22mm Bore 12,000 MOS (rpm).

Kennedy® Extension Cables for Site Use

Waterproof spring loaded socket caps. Available as 1.5mm2 core cables rated to 16A over six hours and 2.5mm2 core cables rated to 32A over six hours (except KEN-282-2400K, rated at 16A). Plugs and sockets conform to BS 4343 : 1968.

110V 2.5mm Core

Freud Circular Saw Blades

Anti-kickback Design: Kickback is caused by over-feed. It happens so quickly it can be impossible to react before injury occurs. On a table saw the wood is thrown back violently, on a radial arm saw the blade climbs quickly out of the cut and on a hand held saw the saw is pushed out of the cut. Freud's design reduces this. Each tooth is followed by a limiter, which restricts bite to the maximum safe amount. Teflon Coating. Resistant to friction and heat build-up. Teflon coated blades last longer, cleaning is easy and the distinctive coating also gives rust resistance.Whisper Quiet Expansion Slots: A question-mark shaped slot allows for the necessary expansion yet reduces noise. Laser Cut, High Strength Bodies: The use of precision lasers to avoid unwanted stress in the metal. The method also allows the use of higher strength steel (40 to 45 Rc). These bodies remain true, even after years of use. Tensioned Blades for Superior Flatness: Pre-tensioned blades ensure years of smooth operation. The process is computer controlled and was designed and built by Freud. Advanced Tri-Metal Tip Brazing: Copper alloy is sandwiched between layers of silver alloy (Copper is soft and will stretch without residual stresses, insulating the shoulders from impacts.)

Blue Line - Fine

Cross cut blades, designed with a high TPI. Suitable for cross grain cutting solid wood giving a good finish.

Makita Batteries for Cordless Tools

Lithium-ion batteries are 40% lighter than a similar Nickel Metal Hydride (Ni-MH) battery. Lithium-ion batteries feature a high energy density technology that will deliver 430% more working capacity during the lifetime of this battery compared to Ni-Cad batteries. Lithium-ion batteries have an extended length of time during which they hold their charge - even after a long period of storage the batteries will deliver their power.

Li-Ion Batteries 'Plug-In' Type

Charger compatibility: DC07SA, DC10WA.

PCL Plastic Blow Gun

BG5002
The body is moulded from a special acetalyc resin to resist damage, staining and contamination with a 100% brass inner valve. The blow gun adjusts the airflow gradually for delicate working. Suitable for use with both air and water. Recommended maximum working pressure of 18 bar (265psi).

Engis Hyprez Oilstones

Manufactured from carefully graded abrasive particles, mixed with the appropriate bonding agents and fired in electric or gas ovens to produce a stone suitable for roughing out cavities and dies to commercial finishes.

Hyprez R.G. Medium Silicon Carbide

This stone is a mainstay, designed for general use. Length: 150mm.

Makita 13mm Hammer Drill

Variable 2 speed with forward & reverse action. Supplied with: side handle, depth gauge. Power input: 720W. No load speed: 0-1,200 & 0-2,900rpm. Blows per minute: 0-24,000 & 0-58,000bpm. Capacities: steel 13mm, masonry 20mm, wood 40mm.

Available in 240V and 110V.

HP2050

Osaki™ Hobbyist Mini Machines

Osaki™ mini machines include a mini lathe, mini bench drill and mini milling/drilling machine. These are ideal for the hobbyist, their small size make them ideal for use in the home workshop/garage. Whilst being small they retain a lot of the features found on larger industrial machines, either as standard or available as accessories. For DIY use. Not warranted for industrial use.

Mini Milling/Drilling Machine

A must for model makers. Bench mounted, this Milling/Drilling machine has a spindle rotation of of up to 45°, making it a very capable tool. An assortment of useful accessories are available. This versatile tool has been manufactured to meet European Machinery Directive 98/37/EC and is both CE and RoHS compliant.

Specifications:
Swing over bed: 180mm.
Drilling capacity: 13mm.
End milling capacity: 16mm.
Face milling capacity: 30mm.
Headstock travel (Z): 180mm.
Cross axis: 100mm.
Longitudinal axis: 220mm.
Spindle rotary angle: +/-45°.
Output power: 350W.
Spindle speed: Low range 0-1100rpm +/-10%. High range: 0-2500rpm +/-10%.
Spindle taper: MT3 or R8.
T-slot: 12mm.
Net/gross weight: 50/68kg.
Packing size: 540 x 500 x 760mm.

FOR DIY USE
Not warranted for industrial use.

Kennedy® Wire Wheels & Brushes

Industrial rotary wire wheels & brushes are available as a comprehensive range including circular brushes, shaft mounted arbor style and de-carbonising brushes for use with power tools, machine tools and flexible drives.

Cup Brushes - Threaded Bore

Multi purpose brush for removal of rust, paint and burrs. Ideally suited for use on bench machines and angle grinders. 30 SWG

Kennedy® Wire Wheels & Brushes

Industrial rotary wire wheels & brushes are available as a comprehensive range including circular brushes, shaft mounted arbor style and de-carbonising brushes for use with power tools, machine tools and flexible drives.

Cup Brushes - Plain Bore

Multi purpose brush for removal of rust, paint and burrs. Ideally suited for use on bench machines and angle grinders. 30 SWG