York? High Performance Flap Discs

High performance alternative to sanding discs. Have the advantage over depressed centre grinding discs on light gauge sheet metal where surface finish is important. Overlapped abrasive strips slowly wear away revealing fresh abrasive, ensuring the disc always cuts effectively, reducing clogging, provides constant finish throughout disc life, generates less noise and heat - less blueing. No backing pads needed - fits directly onto machine. Safe to use at 80m/s on any grinder. Tested at 150m/s and approved by the German Grinding Wheel Authority (DSA).

Aluminium Oxide Grade Glass Fibre Backed (General-Purpose - Non-Scratch)

100mm Dia x 16mm Bore 15,300 MOS (rpm).

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness. Operating speed range is 6000-40000rpm.

Cylindrical Plain End

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HCS - Medium Duty (Pack 5)

Jigsaw Blade (Equivalent to Bosch T119BO)
Application: wood 20mm, plastic 20mm. For cutting curves.
Blade: HCS medium duty, wavy set tooth form.
Tooth pitch: 2.5mm.

Effective length: 50mm.

Pack of 5.

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.

Round Tree

Cut 3 - Rapid Cut
For use on softer non-ferrous and plastic materials i.e. aluminium, fibreglass, plastics, hard rubber and zinc alloy.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'W' Shape. Shank Dia. 3mm

Shape W144. Grade: RA100. Diameter: 3mm. Length: 6mm. Max. rpm: 100,000. Weight per 10: 20g.

Bosch Jigsaw Blades

Application: For thick construction timber, softwood 5-100mm, chipboard, wood core plywood, fibre board. Side set ground teeth. Effective length: 126mm. Pitch: 4.0.

Carbon Steel For Wood & Plastics (Pack 5)

York? Flap Wheels

Shaft mounted flap wheels can be used in portable air or electric power tools, including tyre buffers, flexible shafts and hand drills. Manufactured from highest quality industrial cloth. Used for a wide range of applications such as removal of rust, cleaning up welds and sanding wood prior to painting. Boxed in 10s except for 60 x 50 and 80 x 50 which are packed in 6s. Recessed hub design for maximum access in tight corners.

6mm Shank

50mm Dia x 30mm Height 12,300 MOS (rpm)

3M Stikit™ Discs 245

Stiff E-weight paper gives a strong backing and long product life. Resin bond resists heat to prevent premature "burning". For initial and intermediate sanding on solid wood furniture, wood and metal door frames and other hard and soft wood, plastic and metal surfaces.
Use on: Wood, Metal, Paints, Fillers, Plastics.
Mineral: Aluminium Oxide.
Backing: E Weight Paper.
Coating: Open.
Bond: Resin.

Plain (no holes)

Diameter: 150mm.

Kennedy® Plasterers' Lights

Designed for use by plasterers' and painters' where there is a need to eliminate shadows. Lightweight, portable and weatherproof 110V lights with two 110V outlet sockets. Available in 2 versions as a folding or tripod type.

Plasterers' Light - Folding Type

2 x 18W 40V worklight with non corrosive A-frame design. Lightweight, portable and with 2 x 110V power outlets. Complete with 5m cable. Rated IP65. Works with 2ft (18W max.) low energy fluorescent tubes. (Supplied separately).

High Speed Grinder

Heavy duty die grinder with high power motor. Suitable for grinding and sharpening in confined spaces. Improved tool life due to the "Super Joint System - SJS", absorbs the shock created by accidental wheel lock during operation to protect the gear, collet and coupling for longer tool life. Power input: 750W. Collet size: 8mm or 1/4". No load speed: 7,000 - 28,000rpm.

GD0800C