York High Performance Flap Discs

High performance alternative to sanding discs. Have the advantage over depressed centre grinding discs on light gauge sheet metal where surface finish is important. Overlapped abrasive strips slowly wear away revealing fresh abrasive, ensuring the disc always cuts effectively, reducing clogging, provides constant finish throughout disc life, generates less noise and heat - less blueing. No backing pads needed - fits directly onto machine. Safe to use at 80m/s on any grinder. Tested at 150m/s and approved by the German Grinding Wheel Authority (DSA).

Aluminium Oxide Grade Glass Fibre Backed (General-Purpose - Non-Scratch)

127mm Dia x 22mm Bore 12,000 MOS (rpm).

York? Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness. Operating speed range is 6000-40000rpm.

Cylindrical Plain End

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

York Grinding Wheels

Vitrified bond for precision grinding. Unaffected by water, acid and oils. All 1,1/4?? bore, supplied with 1??, 7/8??, 3/4??, 5/8?? & 1/2?? bore nylon bushes. Tough general-purpose aluminium oxide which is hard wearing. Used for surface and off hand grinding. Refined aluminium oxide with a faster grinding operation. Suitable for high speed steels, precision grinding and general surface grinding. Silicon carbide, used on low tensile strength materials, non ferrous metals and carbide tool grinding. All York grinding wheels are supplied in a unique storage box, which helps prevent chipping and other accidental damage. Spare cases available on request.

3" Bore

York? Fibral XL Unitised Wheels

Produced by adhesively bonding and compressing web together to form a slab from which wheels are then cut.
Maximum rpm: 51mm dia: 16,000rpm, 76mm dia: 9,500rpm, 152mm dia: 4,700rpm.

XL Unitised Wheels

Size: 76 x 12 x 6.5mm.

York? Flap Wheels

Shaft mounted flap wheels can be used in portable air or electric power tools, including tyre buffers, flexible shafts and hand drills. Manufactured from highest quality industrial cloth. Used for a wide range of applications such as removal of rust, cleaning up welds and sanding wood prior to painting. Boxed in 10s except for 60 x 50 and 80 x 50 which are packed in 6s. Recessed hub design for maximum access in tight corners.

6mm Shank

50mm Dia x 25mm Height 12,300 MOS (rpm)

York? Mandrels

For use with Cartridge Rolls. This steel adaptor is used to secure and hold both tapered and parallel sided cartridge rolls to air grinders or electric drills. This holder is used by sliding the cartridge roll onto the mandrel pilot until the bottom of the abrasive touches the threaded steel area. Simply screw the cartridge roll onto the threads to secure. Your mandrel should be at least 13mm longer than your cartridge roll.

York? Flap Wheels

Shaft mounted flap wheels can be used in portable air or electric power tools, including tyre buffers, flexible shafts and hand drills. Manufactured from highest quality industrial cloth. Used for a wide range of applications such as removal of rust, cleaning up welds and sanding wood prior to painting. Boxed in 10s except for 60 x 50 and 80 x 50 which are packed in 6s. Recessed hub design for maximum access in tight corners.

6mm Shank

40mm Dia x 20mm Height 15,300 MOS (rpm)

York? Drum Holders

Suitable for use with chucks/collets on all portable power and air tools. For use with spiral bound abrasive sanding bands. Self expanding when in use for a secure grip on the band. All shanks are 6mm except where marked * which has an 8mm shank.

York? Cartridge Rolls

Spirally wound Aluminium Oxide cloth rolls that wear in use constantly exposing new abrasive. Used for weld flash removal, deburring, blending and polishing applications. Available in two types. A steel mandrel must be used to secure the abrasive to the tool.

Taper Type

Tapered for angles, corners and irregular or concave surfaces.

York? Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness. Operating speed range is 6000-40000rpm.

Cylindrical-End Cutting

Cut 6 - Double Cut
Crosscut and double cut to improve control and chipbreaks. Manufactured from high grade tungsten carbide for general purpose use.