Mitutoyo Micrometer Stand For Digimatic Type

Designed specifically for use with Mitutoyo digimatic micrometers up to 50mm/2". Cast iron, attractively enamelled with clamping joints.

156 series

Interchangeable Rod Type

These are lightweight, well balanced and rigid. Satin-chrome finish with hardened, ground and lapped measuring screw. Each micrometer of less than 300mm (12") is supplied with convenient handle to reach into deep holes. The set also includes spacing collar, a series of precision measuring rods and a dull chrome plated micrometer head. Spacing collars are designed for making up for the limited stroke of the micrometer head. Each rod marked with length. Easily reset - adjustment positive and permanent. Anvil is made from high grade steel, hardened, precision ground, micro-lapped and adjustable. Spanner wrench supplied with each micrometer. Accuracy: Instrument Error: /-(6L/50) mu m; L maximum measuring length

Series 141

Digimatic Type Absolute Calipers

With SPC Data output. Inch/metric conversion. On/Off. Zero set at any point. Data/Hold facility. Complete with power supply battery 1 off SR44.

500 series

Resolution 0.01mm/0.0005"

Spline Micrometers - Enamelled Frame

Small carbide tipped (3mm dia. x 10mm) anvils to fit around and into splined shafts, slots and keyways. Satin chrome finish thimble and sleeve, constant force ratchet and positive locking clamp. Accuracy: Parallelism: (2L/100) mu m (fraction rounded down). Flatness: 0.3 mu m. Instrument Error: /-3 mu m L maximum measuring length.

111 Series

Screw Thread Micrometer

Interchangeable V-anvils allow various pitches to be measured with a single micrometer. With ratchet stop. Accuracy: 0-75mm /-4 mu m, 75-100mm /-5 mu m. Anvils supplied separately.

126 Series

Heavy Duty Vernier Caliper

Thumb wheel and locknut with fine adjustment. Round measuring faces for accurate ID measurement. Satin chrome finish with clear easy read graduations.

Series 160

Metric & Imperial Reading Graduation: 0.02mm/0.001"

Battery Cover

Battery Cover for ABSolute Series 500 Digimatic Calipers

Micrometer Heads

Spindle Diameter: 6.35mm - Tungsten Carbide Tipped. Spindle Housing Diameter: 10mm. Spindle Pitch: 1mm/.025mm. Main Body Diameter: 18mm. Overall length: 109mm. Accuracy (full scale): Metric: /-2 mu m Imperial: /-0.0001"

Series 150

Enamel Finish Interchangeable Anvil Micrometers

With one-piece carbide tip spindle and interchangeable hardened anvils with ground threads. Micro-lapped anvil and spindle faces, perforated frame with enamel finish. Supplied with standards, ratchet stop, positive locking clamp and supplied in a wooden or plastic (depending on size) storage case. Accuracy: Flatness: 0.6mm up to 300mm, 1.0mm up to 300 - 1000mm. Parallelism: (2L/100)mm (fraction rounded down.) Instrument Error: /-(4L/75)mm (fraction rounded up.) L maximum measuring length.

Series 104

Enamel Finish Interchangeable Anvil Micrometers

With one-piece carbide tip spindle and interchangeable hardened anvils with ground threads. Micro-lapped anvil and spindle faces, perforated frame with enamel finish. Supplied with standards, ratchet stop, positive locking clamp and supplied in a wooden or plastic (depending on size) storage case. Accuracy: Flatness: 0.6mm up to 300mm, 1.0mm up to 300 - 1000mm. Parallelism: (2L/100)mm (fraction rounded down.) Instrument Error: /-(4L/75)mm (fraction rounded up.) L maximum measuring length.

Series 104