Rotabroach Mini Cutter Accessories

To suit Rotabroach Mini Cutters.

Pilots

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'W' Shape. Shank Dia. 3mm

Shape W146. Grade: RA80. Diameter: 3mm. Length: 13mm. Max. rpm: 100,000. Weight per 10: 20g.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'B' Shape. Shank Diameter 3mm

Shape B123. Grade: RA80. Diameter: 5mm. Length: 5mm. Max. rpm: 100,000. Weight per 10: 20g.

3M 734 Wet or Dry? Silicon Carbide Paper

Aggressive fast cutting waterproof silicon carbide paper, for use on paints, lacquers and fillers.

Sheets

Size: (W)230mm x (L)280mm. Available in several grades.

York Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.
N.B. - 3mm Shank

Ball Shape

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Kennedy® Wet or Dry Silicon Carbide Paper

Silicon Carbide is waterproof-resin bonded to paper suitable for wet and dry production polishing and finishing of a wide range of materials including metals, plastics, paintwork, ceramics etc.

Wet or Dry Paper Sheets

Size: (W)230mm x (L)280mm. Available in several grades.

Rotabroach Mini Cutters

For perfect holes in sheet metal, pipes & plastic. Cut clean, burr-free holes in seconds with new Roatabroach Mini-Cutters, the professional solution to holemaking in sheet metal, pipes and plastics. Mini-Cutters produce holes by removing a 'disc' of metal and have precision ground teeth and flutes to rapidly remove waste material, so they are fast, smooth and highly accurate. Now they come with a new and more aggressive tooth geometry to give high higher performance and longer cutting life on stainless steel and other difficult materials. No toolbox is complete without Mini-Cutters for clean, precise and effortless holecutting every time. Over 3 times faster than twist drills Mini-Cutters have multiple teeth and an annular
cutting action with no 'dead centre' area as with a twist drill. It means that less pressure is required to make the hole, so there is less risk of deforming sheet metal. This highly efficient cutting action also ensures minimal burring on breakthrough, reducing or completely eliminating the need for additional finishing work. Last up to 300 times longer than hole saws Holesaws have stamped teeth which only remove
small particles of metal with each revolution whereas Mini-Cutters are precision ground cutting instruments which slice their way through sheet metal without leaving burrs or jagged edges. Because they are made from M2 High Speed Steel,
they retain their sharpness to give a longer, more reliable cutting life over thousands of holes.

DeWALT Routers

The DW615 plunge router from DeWALT has electronic speed control to ensure a consistent finish is achieved in all grades of timber, aluminium and plastics since the electronic control ensures the selected speed is maintained under any load.
Whilst soft start eliminates any small initial movement that might misalign the cutter

Other features include:
Lightweight and compact design increases ease of use as the cutter remains visible at all times for error free routing.
Two column precision guide for plunging accuracy in a high quality aluminium housing with phosphor bronze bushing so that carefully controlled plunge cuts can be made.
3 stage depth stop adjustment enables recesses of various depths to be machined in one operation without time consuming setting up.
Spindle lock mechanism for quick and easy cutter changes with a single spanner.

Available as:
110v Order Code: DEW-272-6150K.
230v Order Code: DEW-272-6150R.

DW615 Plunge Router

DW615 Plunge Router Specifications:
Power Input: 900W.
Power Output: 590W.
No Load Speed: 8000-24000rpm.
Plunge Stroke/Movement: 55mm.
Collet Size: 6-8mm
Max. Cutter Diameter: 36mm.
Supplied complete with:
Parallel fence & 2 guide rods.
17 mm guide bush.
Dust extraction adaptor.
17/13mm & 6mm spanners.
6mm collet (¼").

Hand/Arm Vibration: 7.8 m/s2
Uncertainty K 1 (Vibration): 1.7 m/s²
Sound Pressure: 88dB(A)
Acoustic Pressure: 89dB(A)

1/4 Sheet Palm Sander GSS 140A

1/4 sheet palm sander
Easy-Fit system with automatic paper tensioning.
Easy-Fit uses Velcro type fastening system or plain paper.
Fitted with Microfilter integral dust extraction.
Filters particles 100 times smaller in diameter than a human hair.
Large dust capacity allows for extended periods of sanding.

Power input: 180W
Orbit Diameter: 1.6mm
Pad Size: 113 x 105mm
Nett Weight: 1.41kg

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.