Magnetic Vee Blocks

Powerful magnet in a precision ground mild steel case. The vee block can be used on its base, side or end to hold components for machining operations. The large vee can hold diameters up to 65mm and the smaller vee diameters up to 20mm. The on/off switch toggles both vees simultaneously. Suitable for holding cylindrical and complex workpieces for marking, spark erosion, grinding, measurement and inspection operations. Magnetic adhesion (top & bottom faces): 200/150Kg

Kennedy Aluminium Pipe Wrenches

Jaws are serrated in the opposite direction to ensure a secure grip. Used mainly in the plumbing industry for gripping pipes and nuts. Lightweight aluminium alloy handles. As robust as heavy duty cast iron wrenches. All moving parts are heat treated.

Thor Soft Faced Hammers

A safer alternative for striking machined surfaces than conventional steel hammers. The impact resistant striking faces shape themselves to the component being struck, minimising rebound damage to the component and reducing noise pollution in the work place. The striking faces can be easily replaced once they have become worn. Available as standard, with a choice of 5 interchangeable face types:

Plastic Face

Malleable iron head, fitted with two white high molecular weight polythene striking faces for high impact applications.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from carbon steel. These traditional designs are used by tradesmen in all industrial environments. Suitable for a wide range of general duty applications, ideal for dismantling timber constructions, opening packing cases and removing nails (depending on the type of bar). Also used in assembly applications offering safe leverage and alignment capability.

The Kennedy ?RASCAL BAR?

The Right Angled Seam Chisel And L Bar has been specially designed by Kennedy Tools for the separation of hard to reach spot welds and bonded panels as well as coping with the many traditional uses for pry & wrecking bars.
Features & Benefits
?Easily separates hard-to-reach spot welded or bonded panels
?Sharpened on three edges, the sharp end allows for penetration between the panels and both side edges allow for side impact to drive the panels apart without damage
?90 degrees end for use in hard-to-reach pinchweld areas
?Made from a super tough alloy steel
?Will save the technician up to 15 minutes per panel replacement
The Right Angled Rascal Bar with three sharpened edges is designed to allow two-directional hammer use on quarter panels, rockers and any other pinchweld. The sharp end allows for penetration between the panels and the two lower edges allows for side impact to drive the panels apart. The chisel tip can be used for starting seam separation.

Industrial Open Ended Spanners

Made from chrome vanadium steel with a satin finish body and highly polished heads, with a 15 offset. Conform to DIN 3110 & BS 192 : 1982.

A/F

Dial Indicating Torque Drivers

Can indicate torque in two ways - measures and displays torque as it is applied, or measures and displays the maximum torque used, after it has been applied. Ideal for the electronics, electrical and domestic appliance industries. Stainless steel shafts coloured aluminium handles and scaled nylon dials. 1/4" Hex drive. Dual scale. Manufactured to ISO6789:1992.

Standard Type

Torque Range: 50-250 cNm 4-20Ibf.in
Can be used with 1/4" drive. Sliding ?T? bar supplied.

For further specification on this product please see the attached PDF under the catalogue PDF links tab.

Ratchet Type Tap Wrenches

Set contents:
Standard length 1.5 - 2.8, 2.0 - 3.8, 3.0 - 5.0mm.
Extra length 2.0 - 3.8, 3.0 - 5.0mm

Laser Rangefinder

Precise and easy to operate with an illuminated display. Up to 25,000 individual measurements per battery charge due to Li-Ion technology. Small and handy. Reliable aid on any construction site due to robust design.
Laser diode: 635nm 1mW.
Measurement range: 0,05 80m.
Laser class: 2.
Measurement accuracy, typical: +/- 1.5mm.
Measurement time, typical: 0.5s.
Measuring time, max.: 4s.
Dimensions (LxWxH): 111x51x30mm.
Units of measure: m/cm/mm.
Memory capacity (values): 20 + 1.

GLM80

Standard Diagonal Cutting Nippers

Bonded vinyl coated handle. Double polished head and joint. Induction hardened cutting edges. Designed to give added strength at the point yet still fit into confined spaces. The cutting edge is offset at a slight angle to the handles to allow close cuts to a flat surface.

Formers & Guides for Irwin UL223 Bender

Generally compatible with other Irwin-Hilmor pipe benders including GLM, EL25, EL32, CM35, CM42, K3b and Condubend - subject to actual bender pipe size capacity.