Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

3M Roloc Disc Products

Designed for use on portable tools and featuring the convenient Roloc Twist-on, Twist-off fixing system.

361F Cloth Discs

Tough resin bonded aluminium oxide disc for grinding and stock removal. Applications such as weld grinding and finishing.
Maximum rpm. 25mm Discs = 25000 rpm.
38,50 & 75mm Discs = 20000 rpm.

3M Roloc Disc Products

Designed for use on portable tools and featuring the convenient Roloc Twist-on, Twist-off fixing system.

Surface Conditioning Discs

Reinforced Scotch-Brite web designed for cleaning and finishing on all metals. Leaves a burr-free surface for painting and coating for removal of light rust, oxides and coatings.
Maximum rpm.25mm Discs = 25000rpm.
50mm Discs = 23000rpm.
75mm Discs = 18000rpm.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.

York? Flap Wheels

Shaft mounted flap wheels can be used in portable air or electric power tools, including tyre buffers, flexible shafts and hand drills. Manufactured from highest quality industrial cloth. Used for a wide range of applications such as removal of rust, cleaning up welds and sanding wood prior to painting. Boxed in 10s except for 60 x 50 and 80 x 50 which are packed in 6s. Recessed hub design for maximum access in tight corners.

3mm Shank

30mm Dia x 15mm Height 20,400 MOS (rpm)

York? Flap Wheels

Shaft mounted flap wheels can be used in portable air or electric power tools, including tyre buffers, flexible shafts and hand drills. Manufactured from highest quality industrial cloth. Used for a wide range of applications such as removal of rust, cleaning up welds and sanding wood prior to painting. Boxed in 10s except for 60 x 50 and 80 x 50 which are packed in 6s. Recessed hub design for maximum access in tight corners.

6mm Shank

50mm Dia x 30mm Height 12,300 MOS (rpm)

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness. Operating speed range is 6000-40000rpm.

Cylindrical Plain End

Cut 3 - Rapid Cut
For use on softer non-ferrous and plastic materials i.e. aluminium, fibreglass, plastics, hard rubber and zinc alloy.

York? Quick Change Screw Fitting Discs

For general use including blending welds and removing machining marks. Also suitable for use on mild contours as well as flat surfaces. Quick change screw fitting ensures that the disc is always perfectly centred without adhesive, moving parts or centre screw damage to the workpiece. Higher speeds can be attained resulting in faster stock removal reduced man-hours and increased productivity. Available in 25mm, 38mm, 50mm, 75mm and 100mm diameters for the abrasive discs. Also available in a surface preparation material that is designed for smoothing surfaces prior to painting, removing rust, oxides, imperfections and blending out grit disc marks to produce fine finishes on metal. All discs are compatible with 3M ROLOC? system holders.



Zirconia Alumina Abrasive Discs for grinding and finishing of stainless steel.

3M Garnet Paper

110N
A flexible "A" weight garnet paper for hand sanding on wood.

Sheets

Size: (W)230mm x (L)280mm. Available in several grades.

Kennedy® Wet or Dry Silicon Carbide Paper

Silicon Carbide is waterproof-resin bonded to paper suitable for wet and dry production polishing and finishing of a wide range of materials including metals, plastics, paintwork, ceramics etc.

Wet or Dry Paper Sheets

Size: (W)230mm x (L)280mm. Available in several grades.