Quickmike ABSOLUTE Digimatic Micrometer

The Quickmike provides a speedy spindle feed of 10mm/.4” per thimble rotation as compared to the conventional micrometer with 0.5mm/.025” per rotation. Its wide 30mm/1.2” measuring range allows various workpieces with different shapes to be measured quickly.
Non-rotating spindle and the new ratchet friction thimble.
Speedy spindle feed of 10mm/rev.
With absolute linear scale.
IP54 dust/water protection (when not connected with data output cable).
With SPC data output.
With a standard bar to set the origin point (for models with a range over 30mm/1.2”).
Supplied in fitted plastic case.


Technical Data
Resolution: 0.001mm or .00005"/0.001mm
Flatness: 0.3µm/.000012”
Parallelism: 2µm/.00008” for models up to 80mm/3.2” 3µm/.00012” for models up to 105mm/4.2”
Measuring faces: Carbide tipped
Display: LCD
Battery: SR44 (1 pc.), 938882
Battery life: Approx. 3 years under normal use
(1 year for models over 30mm / 1.2”)
Dust/Water protection level: IP54

Function
Origin-set, Zero-setting, Data hold, Data output, inch/mm conversion (inch/mm models)
Alarm: Low voltage, Counting value composition error



Range: 0 - 30.8mm/0 - 1.2"
Accuracy: ±.0001"

Enamel Finish Interchangeable Anvil Micrometers

With one-piece carbide tip spindle and interchangeable hardened anvils with ground threads. Micro-lapped anvil and spindle faces, perforated frame with enamel finish. Supplied with standards, ratchet stop, positive locking clamp and supplied in a wooden or plastic (depending on size) storage case. Accuracy: Flatness: 0.6mm up to 300mm, 1.0mm up to 300 - 1000mm. Parallelism: (2L/100)mm (fraction rounded down.) Instrument Error: /-(4L/75)mm (fraction rounded up.) L maximum measuring length.

Series 104

Micrometer Setting Standards

For zero adjustment of outside micrometers. Accuracy: Flatness: within 0.3 mu m. Parallelism: within 2 mu m

167 Series (Micrometer NOT included)

Mitutoyu Digital Blade Micrometer

422-330
Anvil and the spindle have a blade for measuring the groove diameter of shafts, keyways, and other hard-to-reach portions. Ratchet stop, Origin-set, zero-setting, data hold, data output. Inch/mm conversion.
Accuracy: ±.00005”/±1mm.
Resolution: 0.00005”/0.01mm.

LCD Digimatic height gauge that displays in inches or metric units. Features include data output to transmit results to a mini-processor or computer for statistical process control (SPC). Dual-column beam provides stability that helps promote accurate measurements. Hand-operated feed wheel raises and lowers the gauge for ease of measurement. Comes with an SR44 battery.

192-632-10 Digital Height Gauge

• Measurement range: 0" - 24"/0 - 600mm, with selectable
resolution of 0.0005"/0.01mm or 0.0002"/0.005mm
• LCD digital readout displays sharp figures for viewing ease
• Hand-operated feed wheel for measurement ease, selectable for
coarse or fine travel
• Two reference height presets for making comparison
measurements
• Statistical process control (SPC) output transmits results to
a Mitutoyo miniprocessor or computer

Screw Thread Micrometer

Interchangeable V-anvils allow various pitches to be measured with a single micrometer. With ratchet stop. Accuracy: 0-75mm /-4 mu m, 75-100mm /-5 mu m. Anvils supplied separately.

126 Series

Water Resistant Digimatic External Micrometers

6 models of water resistant micrometers suitable for use in areas where there is a high risk of coolant splash. Large LCD display. Inch/metric conversion. Origin setting. Auto power off. IP-65 coolant proof. Tungsten carbide tipped measuring faces. Conform to BS 870. Resolution: 0.001mm/0.00005".

Accuracy:
0 - 75mm plus/minus 1 mu m.
75 - 100mm plus/minus 2 mu m.
Flatness: 0.3 mu m.
Parallelism:
0 - 50mm 1 mu m.
50 - 100mm 2 mu m.

293 series

Pocket Type - 32mm Diameter Face

9.5mm body for narrow lands between shoulders or in a bore. With jewelled bearings and precision miniature pivot bearings for almost friction free movement of the contact point. Contact point is reversible by lever allowing measurement of the top or bottom surface of any workpiece. Bezel and dial are adjustable.

Series 513

Enamel Finish Interchangeable Anvil Micrometers

With one-piece carbide tip spindle and interchangeable hardened anvils with ground threads. Micro-lapped anvil and spindle faces, perforated frame with enamel finish. Supplied with standards, ratchet stop, positive locking clamp and supplied in a wooden or plastic (depending on size) storage case. Accuracy: Flatness: 0.6mm up to 300mm, 1.0mm up to 300 - 1000mm. Parallelism: (2L/100)mm (fraction rounded down.) Instrument Error: /-(4L/75)mm (fraction rounded up.) L maximum measuring length.

Series 104

Disc Micrometers - Enamelled Frame

For measuring a displacement over a given number of gear teeth, closely spaced sections, ribs, keys and fins etc. Measurable gear pitch: 0.5-6 module. Graduation: 0.01mm (.001"). Accuracy: Parallelism: 0-50mm 4 mu m, 50-100mm (4L/50) mu m. Flatness: 1 mu m. Instrument Error: 0-50mm /-4 mu m, 50-100mm /-6 mu m. L maximum measuring length

123 Series