Micrometer Heads

Standard end, spherical end & reverse reading.
Accuracy:
Metric: ±2µm. Graduation: 0.01mm.
Imperial: ±0.0001". Graduation: 0.001".

Series 148

External Micrometers with Heat Shield

Tapered (on anvil side) for hard to reach places. Supplied without measuring standards. Tungsten Carbide tipped anvils. Accuracy:
Flatness: 0.6 mu m for 0.01mm (0.001") graduation,
0.3 mu m for 0.001mm (0.0001") graduation.
Parallelism: 1 mu m for 0-25mm (0-1") Models, 2 mu m for 25-50mm (1-2") Models.
Instrument Error: /-2 mu m.

Digimatic Output Type Height Gauge

Two measuring modes, ABS (absolute) and INC (incremental), for increased inspection efficiency. Rigid construction ensures repeatable measurements. Six digit lcd display and a minus sign. Provided with data output port for SPC. Preset and zero setting (abs/inc), preset value memory (abs), data Hold, Coarse/fine feed switching, error alarm and low battery alarm. Power supply: Battery 1 off CR2032 supplied.

192-673-10 Digimatic Height Gauge

Magnetic Bases

Designed for maximum flexibility in positioning. Strong permanently magnetic base. Suitable for stem diameter 6 & 8mm dovetail groove. Column: 77mm

Magnetic Stand

Water Resistant Digimatic External Micrometers

6 models of water resistant micrometers suitable for use in areas where there is a high risk of coolant splash. Large LCD display. Inch/metric conversion. Origin setting. Auto power off. IP-65 coolant proof. Tungsten carbide tipped measuring faces. Conform to BS 870. Resolution: 0.001mm/0.00005".

Accuracy:
0 - 75mm plus/minus 1 mu m.
75 - 100mm plus/minus 2 mu m.
Flatness: 0.3 mu m.
Parallelism:
0 - 50mm 1 mu m.
50 - 100mm 2 mu m.

293 series

Enamel Finish Interchangeable Anvil Micrometers

With one-piece carbide tip spindle and interchangeable hardened anvils with ground threads. Micro-lapped anvil and spindle faces, perforated frame with enamel finish. Supplied with standards, ratchet stop, positive locking clamp and supplied in a wooden or plastic (depending on size) storage case. Accuracy: Flatness: 0.6mm up to 300mm, 1.0mm up to 300 - 1000mm. Parallelism: (2L/100)mm (fraction rounded down.) Instrument Error: /-(4L/75)mm (fraction rounded up.) L maximum measuring length.

Series 104

Micrometer Setting Standards

For zero adjustment of outside micrometers. Accuracy: Flatness: within 0.3 mu m. Parallelism: within 2 mu m

167 Series (Micrometer NOT included)

Large Diameter Type - 36.2mm Diameter Face

Large dial face for easy reading with the installed 2mm (.08") diameter point carbide tipped. These indicators are ruggedly housed within a satin chrome finished case. Bezel and dial are adjustable for easy zero setting with fully jewelled movements. Automatic reversible contact point is adjustable through 240. The precision miniature pivot bearings give a frictionless movement of the contact point. One piece bezel of crystal design ensures resistance to water and dust.

Series 513

Standard Type - Sets

Pocket Type - 32mm Diameter Face

9.5mm body for narrow lands between shoulders or in a bore. With jewelled bearings and precision miniature pivot bearings for almost friction free movement of the contact point. Contact point is reversible by lever allowing measurement of the top or bottom surface of any workpiece. Bezel and dial are adjustable.

Series 513

Enamelled Frame External Micrometer Sets

Economy type with carbide tipped anvils. Supplied complete with measuring standard.

Accuracy: Flatness: 0.6um for up to 300mm (12").
Parallelism: (2plusL/100)um (fraction rounded down). Instrument Error: plus/minus(1plusL/75)um (fraction rounded up).
Graduation: 0.01mm/.001".
L equals maximum measuring length.

103 Series

Inch
Range: 0-6".
Set contents: 0-1, 1-2, 2-3, 3-4, 5-6" plus 5 Standards.
Weight: 2.4kg.