1/2" Square Drive Screwdriver Bits

Used most often in the automotive and aerospace industries. The weight to strength ratio ensures the reliability and accessibility that is so important in this type of production environment. For insertion and removal of fasteners and fixings using 1/2"square drive tooling. Unique knurled body gives extra grip which is essential for a quick tool change when your hands are greasy/oily. Registered Design No. 2053516UK. Manufactured from chrome vanadium steel and are fully chrome plated with a mirror finish and aluminium free to ensure non sparking. All have ball retaining groove on each face of the square drive. Overall length: 55mm. Bit length: 17mm. Conforms to DIN standards.

Slotted

Kennedy® Cable Strippers

Durable plastic bodies with hardened and ground sharpened steel blades with precise depth of cut adjustment. Spring loaded safety cover, covers the blade when not in use. Ideal for use in electronic assembly, service and maintenance industries.

CS27

Kennedy® Extending Support Prop

This lightweight support prop is designed to give a helping hand when fixing overhead panelling/boarding. It has 125 x 80mm flat plates at both ends with a swivel ball joint for ease of use and to avoid damage to panel when pressure is applied. It has four pre-set locking heights, 1.16 to 2m, 1.46 to 2.3m, 1.76 to 2.6m and 20.6 to 2.9m.

Kennedy Timing Lights

For checking and setting ignition timing on automotive, agricultural and marine engines. Measures ignition spark advance from 0-60. For use on 12V systems. Reverse polarity protected. Accurate to 8,000rpm. 1m long removable coiled power leads. Impact resistant metal case and rubber nose cone. On/off trigger switch. Bright linear Xenon flash tube for daylight use. Focused lens provides concentrated light. Easy to apply inductive impulse pick-up. Built-in check light.

Advance Timing Light

Kennedy® Inserted Pin Punches

Manufactured from chrome vanadium steel. Used for punching out pins and dowels.

Standard Length

Hand Stamps

Manufactured from Sheffield tool steel nickel plated. With chamfered edges to prevent damaging the surface of the workpiece. For making a clear permanent mark legible even after subsequent painting or plating. Positive Indent (Standard)

Letter Sets A - Z Plus &

Tool Boxes

Robust stacking unit for containing four lockable organiser cases, which lift and slide out. The expandable system allows units to be attached on top or side by side. Cases have translucent lid for selecting contents and multi-positional compartment separators. Used for storing up to 4 service cases.
Dimensions (L x W x H): 425 x 350 x 375mm.
Maximum Load: 6kg

It is recommended that no more than 3 organisers should be stacked at one time.

Service Case Organiser

Insulated Spanners

Chrome vanadium single ended open jaw spanners. Spanner dimensions conform to DIN 7446. Fully insulated to conform to VDE 0680/201, IEC 900 & BS EN 60900 standards for safe electrical applications up to 1000V.

Single End Open Jaw

Bahco MTB-25-M-E Bahco Tape Measure with Reverse Blade Print

Body made of a two component elastomer and ABS.
Patented automatic blade locking for quick and easy measurments
Even body length - 3m - 80mm / 5m - 90mm and 8m - 100mm for easy internal measurements
DURA NY-Coat ? Durable, wear-resistant nylon coated blade
Non-reflective blade for better readability
Magnetic S/S tip for ceiling measurement and magnetic pick up
Reverse blade printing for longer vertical measurements
Heavy duty class 11 tape
Blade width 25mm

Open Jaw Slogging Wrenches

Manufactured to DIN 133.



Manufactured from forged and hardened steel with machined drive faces to ensure good contact with the fastener. With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners.