Hose Clip Pliers

Nickel plated, for use on self tightening hose clips

Kennedy® Standard Industrial Terminals - Red Connector

Durable low cost copper or brass connectors. Manufactured as single piece connectors. Electro tinned to protect from corrosion. Insulated with flared entry, colour coded vinyl sleeves. All disconnect terminals supplied with anti-vibration copper sleeve.

Q-MAX Cutters

The non-rotating metal hole cutter is manufactured from high tensile steel heat treated for a long keen cutting life providing burr free accuracy time after time.

To produce the hole a small pilot hole is drilled allowing a connecting bolt to join the punch on one side and the die on the other side of the materials. Pressure is then applied by tightening the bolt and thus the hole is literally punched out.

Capacity:
Mild steel up to 16swg (1.62mm).
Stainless steel up to 16swg (1.62mm).
Sheet copper, brass and aluminum up to 2.0mm.
Plus many other sheet materials and ductile plastic.

Other sizes available on request. Inch 3/8" to 1,3/4 ". Metric 10mm to 80mm. Plus squares and rectangles.

Metric

Ring Slogging Wrenches

Manufactured to DIN 7444.



Manufactured from forged and hardened steel with machined drive faces to ensure good contact with the fastener. With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners.

Kennedy Soft Faced Hammer

Kennedy soft-faced hammers have composite material striking faces that DO NOT have any metal in them that would mark the surface of the work piece. They are a safer alternative for striking machined surfaces than conventional steel hammers that would damage the surface. The impact-resistant composite material striking face shapes itself to the component being struck, minimising rebound damage to the component and reducing noise pollution in the work place.

Nylon Faced Hammer

Kennedy Nylon faced striking hammers have no metal in the hammer faces that can mark the work piece. Each hammer has two replaceable screw-in nylon hammer faces that can be easily replaced when they become worn, without the use of any other tools - minimising down time. The striking faces are reinforced for extra strength and to prevent fracturing from off centre strikes. The nylon hammerheads have a precision moulded screw thread that screws securely into the chrome plate zinc hammerhead, which in turn is fixed to a fully moulded polypropylene shaft with a shock absorbing soft dual material grip, for improved grip and control.
Overall length: 305mm.

For all dimensional specifications please refer to our catalogue.

Mechanics Screwdrivers

Featuring a classic slimline design favoured by the automotive industry. Black high impact plastic handles. Chrome finish alloy steel blades with satin finish. Magnetic tips, hardened and ground to prolong tool life. Flat blades have hexagon bolster to allow extra torque to be applied using a spanner.

Crosspoint

Granton Knives

All Granton knives are available with a choice of red, blue, yellow, green, brown, white or black handles. This system helps prevent cross contamination by assigning coloured handles to particular work areas.

31/2" Vegetable Knives

Short rigid blade. Sharp at tip only. Suitable for peeling vegetables.

Cabinet & Chest Spares

To suit Kennedy, Senator and Yamoto cabinets and chests.

Drawer Liners/Top Mats

For cabinet and chest compatibility, please refer to our catalogue.

Bahco Diagonal Cutting Nippers

Side cutting plier with progressive edges designed to cut hard material such as piano wire close to the joint and to cut softer material as copper wire and plastic insulated wire at the tip. ISO:5749 DIN:5749. Finish: black oxidised, anti-corrosion treated.

Diagonal Cutting Nippers

Length: 180mm.

Chrome Molybdenum Impact Sockets

Impact sockets and accessories are manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings. Conform to: Metric DIN 3129, Imperial SAE USA Federal Standard GGG-W-660A.

AF Deep

1/2? Drive Inch Size, Standard Length, 6-Point
Conform to: SAE, USA Federal Standard GGG-W-660A.