Kennedy® 900mm Pick Up Tool

4 prong steel retractable claw. Flexible steel stem with a spring loaded plunger to open and close jaws. Chrome plated and corrosion resistant. Ideal for recovery of small objects.

Direct Drive Bits for Power Tools

1/4" Hex with ball recess.

Flat

Scraper Set

For fine surface finishing of intricate contour surfaces. This set of three cabinet scrapers offer shaped edges to match any profile. The rectangular one is used on flat surfaces and the concave/convex and goose neck scrapers will suit all types of curved mouldings. Used to manually remove small amounts of material and excels in tricky grain areas where hand planes would cause tear out. Cabinet scrapers are most suitable for working with hardwoods, and can be used instead of sandpaper. Scraping produces a cleaner surface than sanding; it does not clog the pores of the wood with dust, and does not leave a fuzz of torn fibers, as even the finest abrasives will do. Made from Hardened and ground high carbon steel, these scrapers are 0.9mm thick and will stand up to any heavy duty scraping task with minimum tear out. For best results, these scrapers should be burnished to a razor sharp edge.
Shapes:
Goose neck, concave/convex & rectangle.

Industrial Combination Spanners

Manufactured from chrome vanadium steel with a satin finish body and highly polished heads. 15 open jaw angle to shank and ring end offset.
Conform to:
5.5mm - 25mm, 1/4" - 1" AF - DIN 3113.
26mm - 95mm, 11/16" - 2" AF - ASME B107.6.
1/8" - 1/2" Whitworth - DIN 3113 & BS192:1982.
9/16" - 7/8" Whitworth - ASME B107.6 & BS192:1982.

Metric

Electricians VDE Square Section Handle Screwdrivers

Volt-tested to ensure safety on or near electrical equipment up to 1000V AC or 1500V DC. Insulated blades with magnetic tips. Conform with DIN 7438 and DIN EN 60900.

Pro-Torq Diagonal Cutting Pliers

Manufactured from specially selected steels. The dual material grip handle design allows the user to apply the greatest force with the minimum amount of effort Manufactured with a polypropylene core for strength and durability with a soft thermoplastic outer for non-slip comfort grip. Especially suitable for production line environments where repetitive work is undertaken. Double polished head and joint. Induction hardened cutting edges.



Double polished head and joint. Induction hardened cutting edges.

Ring Slogging Wrenches

Manufactured to DIN 7444.



Manufactured from forged and hardened steel with machined drive faces to ensure good contact with the fastener. With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners.

Industrial Combination Spanners

Manufactured from chrome vanadium steel with a satin finish body and highly polished heads. 15 open jaw angle to shank and ring end offset.
Conform to:
5.5mm - 25mm, 1/4" - 1" AF - DIN 3113.
26mm - 95mm, 11/16" - 2" AF - ASME B107.6.
1/8" - 1/2" Whitworth - DIN 3113 & BS192:1982.
9/16" - 7/8" Whitworth - ASME B107.6 & BS192:1982.

A/F

Shrinking Hammers

Highly polished striking heads and cheeks. One flat round face and one milled, serrated square face. Hickory shaft. Manufactured to BS 4114. Specially designed for panel beating on slightly stretched areas of metal. The cross milled face forces small amounts of metal into the spaces created.

Panel Beating Dolly

Manufactured from drop forged medium carbon steel (SAE/AISI 1055). Heat-treated with a polished mirror finish.

Heel Dolly

For general reshaping of contoured panels,raising low spots and general panel beating.