Kennedy Impact Drive Sockets

Kennedy 1,1/2" square drive impact sockets are manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings.

1,1/2" Drive Metric Size, Standard Length, 6-Point
Conform to: SAE, USA Federal Standard GGG-W-660A.

1,1/2" Impact Drive Sockets

Chrome Molybdenum Impact Sockets

Impact sockets and accessories are manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings. Conform to: Metric DIN 3129, Imperial SAE USA Federal Standard GGG-W-660A.

AF Deep

1/2? Drive Inch Size, Deep Length, 6-Point
Conform to: SAE, USA Federal Standard GGG-W-660A.

1" Square Drive Impact Sockets

Impact sockets and accessories are manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings. Conform to: Metric DIN 3129, Imperial SAE USA Federal Standard GGG-W-660A.

BSW

1? Drive BSW Size, Standard Length, 6-Point
Conform to: SAE, USA Federal Standard GGG-W-660A.

Long Tape Measures

Non-reflective steel tape. Nylon coated for maximum durability. High impact ABS plastic case. Flush winding handle. Chrome plated end hook. Tension 20N. Belt clip. Metric and inch measurement. Blade width is 10mm. Manufactured within the tolerance of EEC class II.

Steel Blade

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Kennedy Inspection Lamp with Li-ion Battery

Ideal for use in engine bays and other low light work areas. Main light and spotlight option. Main light lasts up to 2 hours when fully charged. Convenient grip mounted ON/OFF switch. Durable and robust construction. High light output. Sturdy swivel hanging hook. Anti-roll hexagonal shape. Rubber handle and end cup. Supplied with mains charger.

ILR365 - 65 LED Inspection Lamp (Rechargeable Li-ion Battery)

Model number: ILR365
Order code: KEN-503-5080K
LED intensity at 50cm (main light): 1,600Lux
LED intensity at 50cm (spotlight): 200Lux
Charging time: 5hrs
Operating time (main light): 2hrs
Operating time (spotlight): 20hrs
Charger input: 230V ~ 50Hz
Charger output: 5.4V DC 600mAh
Operating voltage: 3.7V
Operating temperature: 0C to 40C
Battery: Li-ion 2,000mAh
Moisture protection (Inspection Lamp only): IP20
Net weight (Inspection Lamp only): 410g

Kennedy Fuel Container

Suitable for transporting and storing petrol, diesel and motor oil. With lever type safety sealing cap and integral carrying handle. Painted inside and out.

10 Litre Heavy Duty Steel Jerry Can (Green)

The 10ltr capacity Jerry Can from Kennedy is manufactured from 16swg steel with fuel resistant lining. A unique wide channel breather helps ensure that when you pour fuel out of the Kennedy Jerry Can it pours as smoothly as possible to reduce spillages. The leak-proof bayonet lid closure allows storage of the can in any position and is additionally secured in position with a locking pin to prevent accidental opening.

UN Approved Class 3. Conform to DIN 7274. GS TUV approved.

Flexible pouring spout available seperately (KEN-503-9300K).

Kennedy Cases - Accessories

Telescopic Handle & Wheel Set for KEN-593-2700K/KEN-593-2780K.

Kennedy Phosphate Finish Adjustable Wrench Service Kits

Consisting of replacement jaw, knurl and pin.

Kennedy Tool Pouches, Holsters and Belts

Kennedy tool pouches, tool holsters and belts are for the professional tradesman or the keen DIY'er. They are an ideal way to keep your tools close at hand when on site.

Our range includes products suitable for both indoor and outdoor use. They are available in a choice of materials from fully waterproof oil tan leather, full grain leather, split or suede leather or man made nylon and polyester fabrics.

Leather Tool Belt

Kennedy heavy duty split leather tool belt, with heavy duty buckle and retaining loop. For use with Kennedy tool pouches.
Overall length: 1170mm

Available in two widths:
40mm Order Code KEN-593-3020K
50mm Order Code KEN-593-3000K