1/2" Square Drive Impact Socket Set

The sockets are manufactured from the highest quality chrome molybdenum steel which is clearly laser etched with the size for easy and rapid identification. Tough, impact-resistant carry case. Conforms to: Metric DIN 3129, Imperial SAE USA Federal Standard GGG-W-660A.

9 Piece Metric

Contents: Standard length: 10, 12, 13, 14, 17, 19, 24, 27 & 30mm.

Protector Sleeves

Contoured high impact resistant plastic grips redirects the force of mishits safely away from your hands preventing injury. Suitable for use with octagonal cold chisels.

1" Square Drive Impact Sockets

Impact sockets and accessories are manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings. Conform to: Metric DIN 3129, Imperial SAE USA Federal Standard GGG-W-660A.

Metric

1? Drive Metric, Standard Length, 6-Point
Conform to: DIN 3129.

Kennedy Tool Pouches, Holsters and Belts

Kennedy tool pouches, tool holsters and belts are for the professional tradesman or the keen DIY'er. They are an ideal way to keep your tools close at hand when on site.

Our range includes products suitable for both indoor and outdoor use. They are available in a choice of materials from fully waterproof oil tan leather, full grain leather, split or suede leather or man made nylon and polyester fabrics.

Electricians Tool Pouch

Manufactured from natural split leather, fully riveted construction.
4 Tool pockets.
7 Tool loops.
T-bar and chain.
Spring clip.
Tape pocket.

Belt not included.
Tools Not Included.

Kennedy® Tapered Gauges

These are called taper gauges only because of their shape. They do not measure tapers they are ideally suited for the rapid accurate checking of the inside diameters of tubing, slot widths, hole sizes, setting calipers etc. Manufactured from spring tempered stainless steel. 0.1mm increments. Rustless. Constant at 20°C. Satin Chrome anti glare finish. Permanent black figures and graduations.

Kennedy Hydraulic Bottle and Trolley Jacks

Kennedy Hydraulic bottle jacks have large cast iron bases with a steel housing and lift cylinder, that has an adjustable notched load saddle. Each jack is fitted with an overload protection valve. Two piece pumping handle also operates hydraulic release.

For use on a firm level surfaces. DO NOT work under the raised vehicle until another means of support, such as axle stands are in place

GS and TUV approved.

For axle stands see order codes: KEN-503-5520K and KEN-503-5530K.

Hydraulic Bottle Jacks

Model number: B234
Maximum load: 2 Metric Tonnes.
Height range: 181 to 345mm Min/Max.
Max saddle adjustment: 48mm.
Weight: 3kg.

(Load ratings are Metric Tonnes i.e. 1 tonne = 1,000kg).
Supplied with spare seals.

Kennedy Chrome Finish Adjustable Wrench Service Kits

Consist of replacement jaw, knurl and pin.

Chrome Molybdenum Impact Sockets

Impact sockets and accessories are manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings. Conform to: Metric DIN 3129, Imperial SAE USA Federal Standard GGG-W-660A.

A/F

3/4? Drive Inch Size, Standard Length, 6-Point
Conform to: SAE, USA Federal Standard GGG-W-660A.

Lever operated vacuums

For use in hand lift applications only. Multiple vacuums used on a single load can only improve handling. If using more than one vacuum tool the ratio of maximum lift capacity does not increase. To lift heavier weights a larger vacuum must be used. All are fitted with a rubber suction which will not damage contact surface during the lifting action. For use on glass, tiles, plastic or other smooth surfaced non-porous material and can also be used for pulling out dents. Hand lift only, must not be used in conjunction with mechanical lifting equipment.



100mm Rubber rubber suction cup. Maximum lift: 45kg.

Hammer Wedges

Manufactured from high grade steel.