External Spring Calipers

Manufactured from high quality polished steel with ground finished points. A circular spring bow joins the legs and a fine adjusting screw is mounted across the legs and is used for setting the distance between the two points. Calipers are used for taking internal and external measurements, also for comparing distances or sizes.

1" Square Drive Impact Sockets

Impact sockets and accessories are manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings. Conform to: Metric DIN 3129, Imperial SAE USA Federal Standard GGG-W-660A.

Metric

1? Drive Metric, Standard Length, 6-Point
Conform to: DIN 3129.

Kennedy Mechanical Pullers

Kennedy three leg mechanical pullers are used for the removal of gears, ball races, bearings, pulleys and sprockets from drive shafts. With a range of reach capacities available (75 to 200mm) selecting the puller for the job could not be simpler. All have double-ended reversible legs so that they can grip internally or externally depending on your requirement.

Always use a three leg puller whenever possible. As they will grip the component being pulled more securely and the load is more evenly distribution across the three legs, this helps to make removal of the component easier and safer.

To select the correct Kennedy puller for the job you will need to determine what spread and reach capacity is required; spread capacity this is the width of the part to be removed and the reach capacity depth of the part to be removed.

For the full range of Kennedy hydraulic pullers and other Automotive tools please refer to our catalogue.

Internal/External Three Leg Mechanical Puller

Open Jaw Spanners

Made from forged and hardened steel. Conform to DIN 894.

Single Ended

TX Sockets

Chrome vanadium. For use with male headed TX fasteners commonly found in the automotive industry. Overall length: 37mm.

1/4" Square Drive Bi-Hexagon Sockets

Ideal for assembly and servicing of small precision mechanisms associated with electrical, electronic, ignition and refrigeration work. All Bi-hexagon unless stated.

Metric

Reversible Ratchet Ring Spanner Set

All ratcheting ring spanners are manufactured from chrome vanadium steel. Rapid tightening or loosening.

5 Piece - AF

Contents: 1/4" x 5/16", 3/8" x 7/16", 1/2" x 9/16", 5/8" x 11/16" and 3/4" x 7/8".

Kennedy High Impact Resistant Tool Case

Manufactured from HDPE resin with extra thick aluminium trim for a tight closure. Fitted with a single steel fully riveted hinge, two chromed locks with keys, four rubber feet, heavy duty handle, a telescopic handle and large wheels for easy transportation. Inside there is a removeable and a hinged tool board, both with 30 elasticated tool loops, document wallet, three small parts organisers and a large base compartment for tools, accessories and spare parts.
Designed to be stacked and is ideal for widely travelled engineers that carry tools, spare parts and components.

Edison™ Multimeters

Edison™ multimeters are an essential and versatile piece of test equipment. They are used by qualified electricians and mechanics alike to perform various essential tests and measurements on delicate electronic systems, automotive devices, mains appliances, and installations. By operating the multi position switch they can quickly and easily set to be a voltmeter, an ammeter or an ohmmeter. Within the Edison™ range of multimeters you will find direct reading multimeters and non-contact reading multimeters.

DM664 Digital Multimeter

DM664 Digital Multimeter specification: Extra large digits, temperature probe and short lead capacitor, removable rubber holster with lead holders. Continuity, diode, transistor hFE, auto power off, overload indication, low battery indicator, tilt stand/hanger.

Voltage (max): 700V AC 1000V DC.
Current (max): 10A AC/DC.
Resistance (max): 200MW.
Capacitance (max): 200mF.
Frequency (max): 20kHz.
Temperature (max): -20 to 1000C.
Safety Rating: Cat III 600V. Cat II 1000V.
1 year warranty.
Supplied with holster.

Bahco Combination Pliers

Chrome vanadium steel with ergonomic handles for superior grip. Specially designed cutting edges for use on material such as piano and spring steel wire. The gripping surfaces are suited for gripping round and flat material. ISO:5746, DIN:5746.

Engineer's Combination Pliers

Length: 180mm. Weight 280g.